Measurement-computing Digital488/80A Manuale Utente Pagina 62
- Pagina / 106
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
EXAMPLE 1: Data Format F0 - ASCII Hexadecimal
PRINT#1,"CLEAR08"
Line 1: Reset the Digital488/80A.
PRINT#1,"OUTPUT08;R0P0C2G2X"
Line 2: Configure Ports 1 and 2 as output.
PRINT#1,"OUTPUT08;F0X"
Line 3: Select ASCII hexadecimal format.
PRINT#1,"OUTPUT08;D4E6BZX"
Line 4: Output ASCII hexadecimal data 4E6B to Ports 1 and 2.
PRINT#1,"ENTER08",
INPUT#2,A$
Line 6: Read data from the Digital488/80A.
PRINT A$
Line 7: Display shows: 4E6B
EXAMPLE 2: Data Format F1 - ASCII Character
PRINT#1,"CLEAR08"
Line 1: Reset the Digital488/80A.
PRINT#1,"OUTPUT08;C5G2R0P0X"
Line 2: Configure all 5 ports as output; select all 5 ports.
PRINT#1,"OUTPUT08;F1X"
Line 3: Select ASCII character format.
PRINT#1,"OUTPUT08;D4>6ZX"
Line 4: Send ASCII character data 4>6 to the Digital488/80A.
PRINT#1,"ENTER08",
INPUT#2,A$
Line 6: Read data from the Digital488/80A.
PRINT A$
Line 7: Display shows: 00000004>6
PRINT#1,"OUTPUT08;D1??2ZX"
Line 8: Send ASCII character data 1??2 to the Digital488/80A.
PRINT#1,"ENTER08",
INPUT#2,A$
Line 10: Read data from the Digital488/80A.
PRINT A$
Line 11: Display shows: 0000001??2
EXAMPLE 3: Data Format F2 - ASCII Binary
PRINT#1,"CLEAR08"
Line 1: Reset the Digital488/80A.
PRINT#1,"OUTPUT08;C5G2R0P1X"
Line 2: Configure all 5 ports as output; select Port 1 only.
PRINT#1,"OUTPUT08;F2X"
Line 3: Select ASCII binary format.
PRINT#1,"OUTPUT08;D1;1011ZX"
Line 4: Send ASCII binary data 1;1011 to the Digital488/80A.
PRINT#1,"ENTER08",
INPUT#2,A$
Line 6: Read data from the Digital488/80A.
PRINT A$
Line 7: Display shows: 0001;1011
EXAMPLE 4: Data Format F3 - ASCII Decimal
PRINT#1,"CLEAR08"
Line 1: Reset the Digital488/80A.
PRINT#1,"OUTPUT08;C5G2R0P0X"
Line 2: Configure all 5 ports as output; select all 5 ports.
PRINT#1,"OUTPUT08;F3X"
Line 3: Select ASCII decimal format.
PRINT#1,"OUTPUT08;D240;165ZX"
Line 4: Send ASCII decimal data to the Digital488/80A.
PRINT#1,"ENTER08",
INPUT#2,A$
Line 6: Read data from the Digital488/80A.
PRINT A$
Line 7: Display shows: 000;000;000;240;165
EXAMPLE 5: Data Format F5 - High-Speed Binary
PRINT#1,"OUTPUT08#3F5X"
Line 1: Select high-speed binary format.
Note: The #3 tells Driver488 to send only the 3-byte command
string
F5X without terminators. If this was not done, the
first data bytes to appear at the output of the
Digital488/80A would be
CR LF or whatever terminators
were selected.
PRINT#1,CHR$(255),CHR$(125)
Line 2: Send high-speed binary data to the Digital488/80A.
56 Digital488/80A Commands
967695 Digital488/80A User's Manual
- User's Manual 1
- Introduction to this Manual 3
- Table of Contents 4
- 7 - Troubleshooting 5
- A - Appendix A 5
- B - Appendix B 5
- Digital488/80A Overview 1 7
- Accessories 8
- Specifications 9
- CAUTION 10
- Data Transfer Speeds 10
- Digital488/80A Setup 2 11
- Hardware Setup 12
- Default DIP Switch Settings 13
- Addressing Mode Selection 13
- Secondary Address Settings 14
- HVCX1 Option Setup 16
- WARNING 16
- Digital I/O Ports 23
- Introduction 25
- Line Voltage Selection 26
- Fuse Replacement 28
- Rack Mount 29
- Bench Top 29
- Power-Up Activation 30
- Programming Examples 31
- C0 is in use 33
- C) command C5 was executed 33
- Digital488/80A Operation 4 35
- Clear (Pin 41) 36
- Data Strobe (Pin 42) 36
- Trigger (Pin 36
- Inhibit (Pin 44) 37
- Service (Pin 45) 37
- External Data Ready (Pin 46) 37
- IEEE 488 Bus Support 38
- Bus Addresses 40
- Bus Terminators 40
- IEEE 488 Background 5 41
- Bus Lines & Bus Commands 42
- Handshake Lines 43
- Data Transfer Lines 43
- Bus Command Groups 44
- More On Service Requests 45
- Digital488/80A Commands 6 47
- Command Syntax 48
- Command Set & Support 49
- Command Summary 50
- - SRQ on Ready 51
- Command Reference 52
- A - Bit Set 53
- B - Bit Clear 54
- C - Configuration 55
- D - Data Output 56
- E? - Query Error Status 57
- F - Data Format 59
- G - Bus Input/Output 63
- H - Handshake 64
- I - Invert 65
- K - End-Or-Identify 66
- L - Buffer 67
- M - Service Request Mask 68
- O - Recall Configuration 69
- P - Port Select 70
- Q - Inhibit 71
- R - Data Ready 72
- S - Save Configuration 73
- T - Test 74
- U - User Status 75
- V - View Configuration 78
- V? - View Version 79
- X - Execute 80
- Y - Bus Terminator 81
- ? - Query 82
- Serial Poll Status Byte 83
- Troubleshooting 7 85
- Buffer Overrun 86
- Query Error Status 86
- Appendix A A 87
- Software Setup 88
- Appendix B B 91
- IEEE 488 Bus Commands 92
- ASCII Codes 93
- ASCII Code Details 95
- Abbreviations 104
- Notes 106
Prodotti e manuali riguardandi Hardware Measurement-computing Digital488/80A
(64 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale