Measurement-computing DataShuttle Manuale Utente Pagina 16
- Pagina / 126
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
1-8 Introduction & Installation of the Data Shuttle
11-13-01
DataShuttle and DynaRes
In any event, please refer to the software provider’s installation manual, or user guide, for specific
information on how to load and run the particular program.
Troubleshooting
–
If you have any difficulty getting your unit to work, refer to the “Troubleshooting”
section in Chapter 2.
:$51,1*
Be sure to turn the power to the DataShuttle and computer off before making or
removing connections.
Always remove the AC adapter from the power line before disconnecting it from the
DataShuttle.
Physical Installation
Installation very simply consists of plugging the DataShuttle’s DB-25 cable into the parallel port outside
your computer. The DataShuttle may be used in combination with any of our data acquisition products.
To Install a DataShuttle
Single Unit Installation
1. TURN THE COMPUTER OFF. Never plug anything into the computer’s parallel port without first
turning its power switch to the “off” position.
2. Connect the parallel input connector, on the left side of the DataShuttle, to the parallel port on your
computer with the provided DB-25 cable. The parallel port on the PC has 25 pins and is often
labelled “Printer” or “LPT.” Computers may have up to four parallel ports; the DataShuttle may
be connected to any one of these.
3. Connect the provided AC Adapter to the 6-9V DC input just to the side of the parallel port of the
DataShuttle. Plug the AC Adapter into an AC power line.
4. Connect the sensors needed for your application: Remove the top cover of the DataShuttle by
removing the four screws in the corners of the unit. Connect the sensors needed for your application
to the DataShuttle screw terminals. Replace the cover. You may wish to refer to the Applications
Reference Manual for examples of particular applications.
Multiple Unit Installation
To install more than one DataShuttle– Follow the steps above to install the first DataShuttle. Then for every
additional DataShuttle you wish to install, simply connect the parallel input port of that DataShuttle to the
passthrough port of the previously installed DataShuttle. You may use the additional DB-25 cables to do
this, or you can plug the next DataShuttle directly into the previous one. If you prefer to keep the units
separate, you may also connect additional DataShuttles directly to any or all of the other parallel ports on
your computer.
In any of these ways, you may connect up to 15 DataShuttles to one computer.
Please note, however, that only two DataShuttles, may be powered off the same 6V, 1 amp AC Adapter.
Therefore, you must connect a new AC Adapter (see Step 3 above) to every third DataShuttle in a series.
This number may vary outside the U.S.
&$87,21
The DS-16-8-5B models are shipped with a 5V DC, ~2.5A regulated adapter instead of
the standard 6V adapter. If you are using DS-16-8-5B model(s) in your installation,
note that each of those units will require its own adapter.
Polarity
- DataShuttle and DynaRes 1
- Table of Contents 5
- 4 - Installing the DynaRes 6
- 5 - DynaRes - Technical Notes 6
- 8 - Installing the ACAO 7
- Technical Notes 7
- 10 - QuickLog Introduction 7
- Introduction 9
- Data Presentation 10
- Dynamic Resolution 10
- Features and Configurations 11
- DataShuttle Model Variations 12
- DataShuttle-RTD 13
- DataShuttle-TC 14
- DataShuttle-5B 14
- Installing Your DataShuttle 15
- Physical Installation 16
- Printer Installation 17
- Keyboard Adapter Installation 17
- Next Steps 17
- Block Diagram 19
- Auxiliary Components 21
- Power Supplies 22
- Examples 23
- Example 3: Ground loops 24
- &$87,21 25
- Digital Components 26
- Installing Pull-up Resistors 26
- Counter/Timer 27
- If You Need Customer Support 28
- Troubleshooting: Operation 29
- Product Specifications 31
- DataShuttle-16 RTD Accuracy 32
- Analog Input 34
- Digital Input/Output 34
- Analog Output 34
- General Information 35
- Introduction to the DynaRes 3 37
- DynaRes System Requirements 40
- Installing the DynaRes 4 41
- Physical Board Installation 42
- Measuring Current 44
- Setting the Base Address 45
- Changing Hardware Interrupts 46
- DynaRes - Technical Notes 5 47
- Recalibration 49
- EDITCAL Utility 49
- DynaRes 8/16 RTD Accuracy 53
- Stability 54
- Input Impedance 54
- Noise Rejection 54
- Common Mode Range 54
- Input Protection 54
- Resolution/Scan Rate 55
- Digital I/O Channels 55
- General Conditions 55
- Types of Terminal Panels 58
- T71 Terminal Panel 59
- Reference Tables 60
- Digital Auxiliary Components 64
- Troubleshooting Q & A 65
- Installing the ACAO 8 71
- Setting the Switches 73
- Multiple Boards 74
- Single Board 75
- Disabling Board 75
- Setting the Switch 75
- Base Address Settings 77
- 8-8 Installing the ACAO 78
- Overview 79
- Editing Calibration Files 81
- Calibration File Format 82
- Using EDITCAL 83
- EDITCAL Selections 84
- 0 to 10V 0.02% 0.01% 86
- Auxiliary Power Output 87
- QuickLog Introduction 10 89
- Setting Up QuickLog 90
- Specifications 91
- I/O Configuration By Channel 92
- Chart Configuration 92
- File Menu 93
- Edit Menu 93
- Options Menu: General 94
- Options Menu: Inputs 95
- Options Menu: Output Meters 95
- Options Menu: Chart 95
- Chart Menu 96
- Run Menu 96
- Window Menu 96
- Calibration Menu 96
- Help Menu 96
- Applications Primer 12 97
- Sensor Connections 98
- Digital Connections 98
- Applications Primer 12-3 99
- 12-4 Applications Primer 100
- Analog Input & Output 13 101
- Thermocouple Types 103
- Strain Gages 104
- Piezoelectric Sensors 105
- RTD Ranges & Resolution 108
- RTD Accuracy 109
- High Voltage Divider 111
- Voltage Output 111
- Current Output 112
- Digital I/O 14 115
- 14-2 Digital I/O 116
- Digital I/O 14-3 117
- Pulse Counting 118
- Cascaded Counter/Timers 118
- Frequency/Rate Measurement 119
- 14-6 Digital I/O 120
- Appendix A 121
- Glossary 123
- Glossary - 2 124
- Glossary - 3 125
- Glossary - 4 126
Prodotti e manuali riguardandi Hardware Measurement-computing DataShuttle
(33 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale